WLAN
These carrier settings are applicable when you select:
802.11bn as the PHY Specification
and UHR TB PPDU as the Generation Mode
Maximum Number of Total Spatial Streams (Nss,total)
Number of Full BW MU-MIMO Users
the 10th Band Allocation Index
the 11th Band Allocation Index
the 12th Band Allocation Index
the 13th Band Allocation Index
the 14th Band Allocation Index
the 15th Band Allocation Index
the 16th Band Allocation Index
Distribute RU in the 1st 80MHz
Distribute RU in the 2nd 80MHz
Distribute RU in the 3rd 80MHz
Distribute RU in the 4th 80MHz
Distribute BWs in the 1st 80 MHz
Distribute BWs in the 2nd 80MHz
Quadrature Angle Adjustment for Waveform 1
I/Q Gain Balance for Waveform 1
Quadrature Angle Adjustment for Waveform 2
I/Q Gain Balance for Waveform 2
Quadrature Angle Adjustment for Waveform 3
I/Q Gain Balance for Waveform 3
Quadrature Angle Adjustment for Waveform 4
I/Q Gain Balance for Waveform 4
Quadrature Angle Adjustment for Waveform 5
I/Q Gain Balance for Waveform 5
Quadrature Angle Adjustment for Waveform 6
I/Q Gain Balance for Waveform 6
Quadrature Angle Adjustment for Waveform 7
I/Q Gain Balance for Waveform 7
RU Setup > User Setup > User Configuration
RU Setup > User Setup > Modulation and Coding
RU Setup > User Setup > Transmit Data
802.11bn Carrier Settings: UHR TB PPDU
RU Setup > User Setup > Impairments
RU Setup > User Setup > Payload
Select the Symbol interval (with guard interval) for the UHR-LTF field. The possible options are:
1x UHR-LTF + 1.6 us
2x UHR-LTF + 1.6 us
4x UHR-LTF + 3.2 us
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:LTF:SINTerval:MODE B|D1|D2|Q1|Q2|B1
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:LTF:SINTerval:MODE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
Q1 |
|
State Saved |
Yes |
Indicates the number of UHR-LTFs. If Maximum Number of Total Spatial Streams is 1, then its value is 1, otherwise its value is the ceiling of (NumOfTotalSpatialStreams / 2.0) * 2.
This is a read-only setting.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:NHELtf? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
1 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Indicates the total number of spatial streams of the current Resource Unit, which is equal to the sum of the Nss for each user.
This is a read-only setting.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:SPATial:NUMBer? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
1 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set the number of transmit chains. When the number of instruments is more than 1, it automatically equals to the number of instruments and can't be changed, otherwise, it is editable.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:NTX <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:NTX? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
1 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Indicates the presence of the extra OFDM symbol for LDPC.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:LDPC:SYMBol <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:LDPC:SYMBol? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
1 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Get or set the PE Disambiguity subfield.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:PE:DISambiguity <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:PE:DISambiguity? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set the value of the L-SIG length field of the UHR trigger-based PPDU that is the response to the trigger frame.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:LSIG:LENGth <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:LSIG:LENGth? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
34 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Enable/disable the user schedule mode. When enabled, the parameters L-SIG Length, LDPC Extra Symbol, PE Disambiguity, and Pre-FEC Padding Factor become editable.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:USER:SCHedule[:STATe] ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:USER:SCHedule[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
OFF |
|
State Saved |
Yes |
Get or set the Pre-FEC Padding Factor.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:PFEC:PADDing:FACTor <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:PFEC:PADDing:FACTor? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
4 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set or Get the Maximum Packet Extension Duration for the current PPDU.
A UHR PPDU may have a Packet Extension (PE) field appended at the end of the PPDU, with possible durations being 0 us, 8 us, 16 us or 20 us. The PE field, when present, shall be transmitted with the same average power as the Data field, and its content is arbitrary.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:PE:DURation PE0|PE8|PE16|PE20
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:PE:DURation? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
PE0 |
|
State Saved |
Yes |
Get or Set the number of MU-MIMO users when compression mode is enabled.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:MIMO:USER:NUMBer <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:MIMO:USER:NUMBer? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
1 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Indicates whether OFDMA or non-OFDMA RU/MRU transmission of UHR TB PPDU is supported for PPDU bandwidth of 160 MHz or 320 MHz. DRU is not supported for non-OFDMA RU/MRU.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:NOFDma[:STATe] ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:NOFDma[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
OFF |
|
State Saved |
Yes |
Gets or sets the RU/MRU index for non-OFDMA UHR TB PPDU.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RINDex RU1|MRU1|MRU2|MRU3|MRU4|MRU5|MRU6|MRU7|MRU8
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RINDex? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
MRU1 |
|
State Saved |
Yes |
Get or set the RU allocation index for the applicable Bands. It may contain multiple small-size RUs/MRUs or a large-size RU/MRU that may span multiple 20 MHz subbands including the current subband. RU allocation bits 000011010 represent a punctured 242-tone RU.
Based on the set bandwidth, the following settings are available:
| 20 MHz |
|
| 40 MHz |
|
| 80 MHz |
|
| 160 MHz |
|
| 320 MHz |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B1
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B1? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
001000000 |
|
State Saved |
Yes |
See the 1st Band Allocation Index for description.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B2
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B2? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
001000000 |
|
State Saved |
Yes |
See the 1st Band Allocation Index for description.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B3
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B3? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
001000000 |
|
State Saved |
Yes |
See the 1st Band Allocation Index for description.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B4
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B4? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
001000000 |
|
State Saved |
Yes |
See the 1st Band Allocation Index for description.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B5
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B5? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
001000000 |
|
State Saved |
Yes |
See the 1st Band Allocation Index for description.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B6
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B6? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
001000000 |
|
State Saved |
Yes |
See the 1st Band Allocation Index for description.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B7
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B7? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
001000000 |
|
State Saved |
Yes |
See the 1st Band Allocation Index for description.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B8
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B8? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
001000000 |
|
State Saved |
Yes |
See the 1st Band Allocation Index for description.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B9
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B9? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
001000000 |
|
State Saved |
Yes |
See the 1st Band Allocation Index for description.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B10
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B10? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
001000000 |
|
State Saved |
Yes |
See the 1st Band Allocation Index for description.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B11
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B11? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
001000000 |
|
State Saved |
Yes |
See the 1st Band Allocation Index for description.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B12
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B12? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
001000000 |
|
State Saved |
Yes |
See the 1st Band Allocation Index for description.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B13
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B13? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
001000000 |
|
State Saved |
Yes |
See the 1st Band Allocation Index for description.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B14
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B14? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
001000000 |
|
State Saved |
Yes |
See the 1st Band Allocation Index for description.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B15
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B15? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
001000000 |
|
State Saved |
Yes |
See the 1st Band Allocation Index for description.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B16
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUALlocation:B16? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
001000000 |
|
State Saved |
Yes |
Enable/disable distributed RUs for 20MHz | 40MHz | 80MHz PPDU.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:DRU[:STATe] ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:DRU[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
OFF |
|
State Saved |
Yes |
Enable/disable distributed RU for the 1st 80 MHz frequency subblock.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:DRU:B80M:FIRst ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:DRU:B80M:FIRst? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
OFF |
|
State Saved |
Yes |
Enable/disable distributed RU for the 2nd 80 MHz frequency subblock.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:DRU:B80M:SECond ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:DRU:B80M:SECond? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
OFF |
|
State Saved |
Yes |
Enable/disable distributed RU for the 3rd 80 MHz frequency subblock.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:DRU:B80M:THIRd ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:DRU:B80M:THIRd? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
OFF |
|
State Saved |
Yes |
Enable/disable distributed RU for the 4th 80 MHz frequency subblock.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:DRU:B80M:FOURth ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:DRU:B80M:FOURth? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
OFF |
|
State Saved |
Yes |
Pattern of Distribute BWs in the 1st 80 MHz frequency subblock.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:DBW:B80M:FIRSt DBW202040M|DBW402020M|DBW80M
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:DBW:B80M:FIRSt? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
DBW80M |
|
State Saved |
Yes |
Pattern of Distribute BWs in the 2nd 80 MHz frequency subblock.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:DBW:B80M:SECond DB202040M|DBW402020M|DBW80M
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:DBW:B80M:SECond? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
DBW80M |
|
State Saved |
Yes |
Pattern of Distribute BWs in the 3rd 80 MHz frequency subblock.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:DBW:B80M:THIRd DBW202040M|DBW402020M|DBW80M
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:DBW:B80M:THIRd? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
DBW80M |
|
State Saved |
Yes |
Pattern of Distribute BWs in the 4th 80 MHz frequency subblock.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:DBW:B80M:FOURth DBW202040M|DBW402020M|DBW80M
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:DBW:B80M:FOURth? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
DBW80M |
|
State Saved |
Yes |
Indicates whether the frame is Uplink or Downlink. The field is set to DL for TDLS and set to UL for UHR TB PPDU.
It is a read-only setting with a fixed value of UL (uplink).
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:LINK? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
UL |
|
State Saved |
Yes |
Get or Set the Base station identifier.The BSS Color field is an identifier of the BSS.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:BSS:COLor <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:BSS:COLor? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
5 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set or Get the remaining time duration in the current TXOP.
Set to 8449 μs to indicate no duration information.
Set to a value other than 8449 μs to indicate the duration information for NAV setting and protection of the TXOP. When the value ranges from 0 to 504 μs, the granularity is 8 μs. When the value ranges from 512 to 8448 μs, the granularity is 128 μs.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:TXOP:DURation <real>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:TXOP:DURation? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
8e-06 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Indicates whether or not spatial reuse is allowed in a subband of the PPDU during the transmission of this PPDU. If allowed, it indicates a value that is used to determine a limit on the transmit power of a spatial reuse transmission.
If the Bandwidth field indicates 20 MHz, 40 MHz, or 80 MHz: Spatial Reuse field for the first 20 MHz subband.
If the Bandwidth field indicates 160 MHz: Spatial Reuse field for first 40 MHz subband of the 160 MHz operating band.
If the Bandwidth field indicates 320 MHz: Each Spatial Reuse subfield is set to the smaller value of the Spatial Reuse 1 and the Spatial Reuse 2 subfields.
Set to 0 (SR disallowed Entry) to disallow SRP-based spatial reuse.
Set to value 1 to 14 corresponding to SRP value for SRP-based SR operation.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:SPATial:REUSe:R1 <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:SPATial:REUSe:R1? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
1 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Indicates whether or not spatial reuse is allowed in a subband of the PPDU during the transmission of this PPDU. If allowed, it indicates a value that is used to determine a limit on the transmit power of a spatial reuse transmission.
If the Bandwidth field indicates 20 MHz, 40 MHz, or 80 MHz: Spatial Reuse field for the second 20 MHz subband. When operating in 20 MHz, this field is set to the same value as Spatial Reuse 1 field. When operating 40 MHz in 2.4 GHz band, this field is set to same value as Spatial Reuse 1 field.
If the Bandwidth field indicates 160 MHz: Spatial Reuse field for second 40 MHz subband of the 160 MHz operating band.
If the Bandwidth field indicates 320 MHz: Each Spatial Reuse subfield is set to the smaller value of the Spatial Reuse 1 and the Spatial Reuse 2 subfields.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:SPATial:REUSe:R2 <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:SPATial:REUSe:R2? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
1 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Get or set the offset to the standard symbol rate in ppm. This error will be added to standard sample clock in the waveform header.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:CLOCk:OFFSet <real>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:CLOCk:OFFSet? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set the baseband quadrature angle adjustment for Waveform 1 before channel fading and mirror spectrum.
The number of parameter groups depends on Number of Transmit Chains (Ntx). Each group is identified with an incremented waveform number, such as Waveform 1, Waveform 2, and so on.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:QUAD:ANG1 <real>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:QUAD:ANG1? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set the baseband IQ gain balance for Waveform 1 before channel fading and mirror spectrum.
The number of parameter groups depends on Number of Transmit Chains (Ntx). Each group is identified with an incremented waveform number, such as Waveform 1, Waveform 2, and so on.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:IQ:GB1 <real>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:IQ:GB1? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set the baseband quadrature angle adjustment for Waveform 2 before channel fading and mirror spectrum.
The number of parameter groups depends on Number of Transmit Chains (Ntx). Each group is identified with an incremented waveform number, such as Waveform 1, Waveform 2, and so on.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:QUAD:ANG2 <real>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:QUAD:ANG2? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set the baseband IQ gain balance for Waveform 2 before channel fading and mirror spectrum.
The number of parameter groups depends on Number of Transmit Chains (Ntx). Each group is identified with an incremented waveform number, such as Waveform 1, Waveform 2, and so on.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:IQ:GB2 <real>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:IQ:GB2? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set the baseband quadrature angle adjustment for Waveform 3 before channel fading and mirror spectrum.
The number of parameter groups depends on Number of Transmit Chains (Ntx). Each group is identified with an incremented waveform number, such as Waveform 1, Waveform 2, and so on.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:QUAD:ANG3 <real>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:QUAD:ANG3? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set the baseband IQ gain balance for Waveform 3 before channel fading and mirror spectrum.
The number of parameter groups depends on Number of Transmit Chains (Ntx). Each group is identified with an incremented waveform number, such as Waveform 1, Waveform 2, and so on.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:IQ:GB3 <real>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:IQ:GB3? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set the baseband quadrature angle adjustment for Waveform 4 before channel fading and mirror spectrum.
The number of parameter groups depends on Number of Transmit Chains (Ntx). Each group is identified with an incremented waveform number, such as Waveform 1, Waveform 2, and so on.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:QUAD:ANG4 <real>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:QUAD:ANG4? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set the baseband IQ gain balance for Waveform 4 before channel fading and mirror spectrum.
The number of parameter groups depends on Number of Transmit Chains (Ntx). Each group is identified with an incremented waveform number, such as Waveform 1, Waveform 2, and so on.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:IQ:GB4 <real>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:IQ:GB4? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set the baseband quadrature angle adjustment for Waveform 5 before channel fading and mirror spectrum.
The number of parameter groups depends on Number of Transmit Chains (Ntx). Each group is identified with an incremented waveform number, such as Waveform 1, Waveform 2, and so on.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:QUAD:ANG5 <real>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:QUAD:ANG5? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set the baseband IQ gain balance for Waveform 5 before channel fading and mirror spectrum.
The number of parameter groups depends on Number of Transmit Chains (Ntx). Each group is identified with an incremented waveform number, such as Waveform 1, Waveform 2, and so on.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:IQ:GB5 <real>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:IQ:GB5? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set the baseband quadrature angle adjustment for Waveform 6 before channel fading and mirror spectrum.
The number of parameter groups depends on Number of Transmit Chains (Ntx). Each group is identified with an incremented waveform number, such as Waveform 1, Waveform 2, and so on.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:QUAD:ANG6 <real>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:QUAD:ANG6? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set the baseband IQ gain balance for Waveform 6 before channel fading and mirror spectrum.
The number of parameter groups depends on Number of Transmit Chains (Ntx). Each group is identified with an incremented waveform number, such as Waveform 1, Waveform 2, and so on.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:IQ:GB6 <real>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:IQ:GB6? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set the baseband quadrature angle adjustment for Waveform 7 before channel fading and mirror spectrum.
The number of parameter groups depends on Number of Transmit Chains (Ntx). Each group is identified with an incremented waveform number, such as Waveform 1, Waveform 2, and so on.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:QUAD:ANG7 <real>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:QUAD:ANG7? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set the baseband IQ gain balance for Waveform 7 before channel fading and mirror spectrum.
The number of parameter groups depends on Number of Transmit Chains (Ntx). Each group is identified with an incremented waveform number, such as Waveform 1, Waveform 2, and so on.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:IQ:GB7 <real>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:IQ:GB7? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set the baseband quadrature angle adjustment for Waveform 8 before channel fading and mirror spectrum.
The number of parameter groups depends on Number of Transmit Chains (Ntx). Each group is identified with an incremented waveform number, such as Waveform 1, Waveform 2, and so on.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:QUAD:ANG8 <real>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:QUAD:ANG8? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set the baseband IQ gain balance for Waveform 8 before channel fading and mirror spectrum.
The number of parameter groups depends on Number of Transmit Chains (Ntx). Each group is identified with an incremented waveform number, such as Waveform 1, Waveform 2, and so on.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:IQ:GB8 <real>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:IQ:GB8? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
The index for each resource unit.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:INDex? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
1 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Enable/disable the Resource Unit (RU).
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>[:STATe] ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
Get the RU/MRU size.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:SIZE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
242 |
|
State Saved |
Yes |
Get the index of the first 20-MHz subband where the RU/MRU is located.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:BAND? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Indicates the total number of spatial streams of the current Resource Unit, which is equal to the sum of the Nss for each user.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:SPATial:NUMBer? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
1 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Get the number of users of the current Resource Unit.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USER:NUMBer? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
1 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:SPATial:CONFigure
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:SPATial:CONFigure? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
000000 |
|
State Saved |
Yes |
Set the contents of the spatial mapping matrix.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:SPATial:MAPPing
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:SPATial:MAPPing? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
1; |
|
State Saved |
Yes |
The index for each user.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:INDex? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Enable or disable the Scrambler.
Scrambles the data to reduce the probability of long sequences of zeros and ones.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:SCRambler[:STATe] ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:SCRambler[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
Select the Channel Coding mode. It encodes the data to enable error correction. It could be BCC and LDPC. Support for BCC coding is limited to less than or equal to four spatial streams, UHR-MCSs 0 to 9, and UHR-MCS 15 (per user in the case of MU-MIMO). BCC support is mandatory for RU or MRU sizes less than or equal to a 242-tone.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:CCODing:MODE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
LDPC |
|
State Saved |
Yes |
Enable or disable the 2x1944 LDPC.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:LDPC:DOUBle1944 ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:LDPC:DOUBle1944? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
OFF |
|
State Saved |
Yes |
Enable or disable the channel encoding function. When it's Off, BCC encoder or LDPC encoder will be bypassed.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:CCODing[:STATe] ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:CCODing[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
Enable or disable the Interleaver. Interleaver interleaves the bits of each spatial stream(changes order of bits) to prevent long sequences of adjacent noisy bits from entering the BCC decoder. Interleaving is applied only when BCC encoding is used.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:BCC:INTerleaver ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:BCC:INTerleaver? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
Enable or disable the LDPC Tone Mapper. LDPC Tone Mapper is equivalent to block-interleaving the tones in each symbol.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:LDPC:MAPPer ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:LDPC:MAPPer? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
Set the number of Spatial Streams used by the current user. Its maximum value is 8 for Single User, while it's 4 for Multi User MIMO.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:NSS <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:NSS? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
1 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set the initial state of the scrambler in decimal format, which is then turned into 7 bits to feed into the scrambler.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:SCRambler:INIT <integer> [:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:SCRambler:INIT? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
99 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Select the MCS Index for current user.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MCS:INDex <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MCS:INDex? |
|
SCPI Example |
|
|
Couplings |
MCS 14 is only applied for UHR TB PPDU, Compress Mode On, bandwidth is greater than or equal to 80 MHz, no preamble puncture exist, and Nss = 1. MCS 15 is only applied for Nss,u= 1, and not supported over MRU 2x996+484 and MRU 3x996+484. |
|
Preset |
8 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Indicates the modulation format determined by MCS index.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MODulation? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
BPSK |
|
State Saved |
Yes |
Indicates the data rate determined by MCS index.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:DRATe? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
|
|
State Saved |
Yes |
Indicates the coding rate determined by MCS index.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:CRATe? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
R12 |
|
State Saved |
Yes |
Enable or disable the MPDU aggregation mode.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:AGGRegated:AMPDu ON|OFF|1|0 [:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:AGGRegated:AMPDu? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
Enable or disable the MAC Layer Padding mode.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MAC:PADDing[:STATe] ON|OFF|1|0 [:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MAC:PADDing[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
Determines the minimum time between the start of adjacent MPDUs within an A-MPDU that the STA can receive.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MMPDu:SSPacing NORestriction|QUARter|HALF|ONE|TWO|FOUR|EIGHt|SIXTeen [:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MMPDu:SSPacing? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
NORestriction |
|
State Saved |
Yes |
Indicates the number of octets in the AMPDU pre-EOF padding carried in the PSDU of the current user. It's the LENGTH defined in the standard. It is equal to the sum of A-MPDU Subframe Length of all MPDUs.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:AMPDu:LENGth? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
294 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
PSDU Length is calculated with Nsym. Nsym depends on original payload length of multi-users.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PSDU:LENGth? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
1058 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Gets or sets the power of the uplink users relative to others.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:POWer <real>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:POWer? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Gets or sets the frequency offset reference to the User carrier.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:FREQuency:OFFSet <real>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:FREQuency:OFFSet? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set the initial phase of the carrier.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PHASe <real> [:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PHASe? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Set the timing offset of the carrier. Timing offset values increment by 1 ps.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:TIMing:OFFSet <real> [:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:TIMing:OFFSet? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Get or Set the offset to the standard symbol rate in ppm. This error will be added to standard sample clock in the waveform header.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:CLOCk:OFFSet <real>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:CLOCk:OFFSet? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
It is visible when the Aggregated MPDU is set to Off.
Displays the index for each MPDU. This cell cannot be edited.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:INDex? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Displays the number of octets in the current MPDU, which is comprised of MSDU, MAC Header and MAC FCS.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:LENgth? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
290 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Use this cell to select the payload data source. The user data of the frame can contain the following data:
All 0s
PN9
PN15
User file
The user file must be in binary form. The least significant bit (LSB) of the first byte in the user data file will be the first bit of the user payload; the LSB of the second byte in the user file will be the ninth bit of the user payload, and so on. If User file is selected as the Data Type, the value displayed in the Data Length field will be equal to the length of the user's data file, up to the maximum data length.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:DATA:TYPE ALL|PN9|PN15|FILE [:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:DATA:TYPE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
PN9 |
|
State Saved |
Yes |
Specify a seed in decimal format to generate a PN9 data sequence. The LSB of the seed comes out first. For example, if you enter a seed value of 10 (1010 in binary), the first 9 bits of the PN9 sequence are 0 1 0 1 0 0 0 0 0, with an increasing index from left to right. For more information, see PN Sequence Generation.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:DATA:PN9:SEED <integer> [:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:DATA:PN9:SEED? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
511 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Specify a seed in decimal format to generate a PN15 data sequence. The LSB of the seed comes out first. For example, if you enter a seed value of 10 (1010 in binary), the first 15 bits of the PN15 sequence are 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0, with an increasing index from left to right. For more information, see PN Sequence Generation.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:DATA:PN15:SEED <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:DATA:PN15:SEED? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
32767 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Click the > button in this cell to select a user file as the data source.
The user file must be in binary form. The least significant bit (LSB) of the first byte in the user data file will be the first bit of the user payload; the LSB of the second byte in the user file will be the ninth bit of the user payload, and so on. If User file is selected as the Data Type, the value displayed in the Data Length field will be equal to the length of the user's data file, up to the maximum data length.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:DATA:FILE
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:DATA:FILE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
|
|
State Saved |
Yes |
Displays the number of data bytes in the user file when it is selected as the payload data source.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:DATA:FILE:LENGth? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-9223372036854776000 |
|
Max |
9223372036854776000 |
Set the number of data bytes in a frame. The value is limited by the MPDU Length.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:DATA:LENGth <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:DATA:LENGth? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
256 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Enable/disable the appending of a MAC FCS check sequence to the data payload.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:FCS ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:FCS? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
Click the > button displayed with this field to open the MAC Header Dialog, which enables or disables pre-pending the MAC header to the data payload. You can select General, RTS, CTS, or ACK format by clicking the down arrow in the top right corner of the Mac Header Dialog. You can set the desired data in each of the individual fields for each format. You can also disable these fields if the data is no longer desired by clearing the Mac Header (hex) checkbox.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer[:STATe] ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:TYPE GENeral|RTS|CTS|ACK
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:TYPE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
GENeral |
|
State Saved |
Yes |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:LENGth? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
30 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:FRAMe[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:FRAMe:SIZE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
2 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:FRAMe:CONTent <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:FRAMe:CONTent? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:DURation[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:DURation:SIZE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
2 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:DURation:CONTent <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:DURation:CONTent? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:ADDRess:A1[:STATe] ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:ADDRess:A1[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:ADDRess:A1:SIZE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
6 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:ADDRess:A1:CONTent <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:ADDRess:A1:CONTent? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-9223372036854776000 |
|
Max |
9223372036854776000 |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:ADDRess:A2[:STATe] ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:ADDRess:A2[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:ADDRess:A2:SIZE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
6 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:ADDRess:A2:CONTent <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:ADDRess:A2:CONTent? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-9223372036854776000 |
|
Max |
9223372036854776000 |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:ADDRess:A3[:STATe] ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:ADDRess:A3[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:ADDRess:A3:SIZE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
6 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:ADDRess:A3:CONTent <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:ADDRess:A3:CONTent? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-9223372036854776000 |
|
Max |
9223372036854776000 |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:SEQ[:STATe] ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:SEQ[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:SEQ:SIZE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
2 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:SEQ:CONTent <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:SEQ:CONTent? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:ADDRess:A4[:STATe] ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:ADDRess:A4[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:ADDRess:A4:SIZE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
6 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:ADDRess:A4:CONTent <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:ADDRess:A4:CONTent? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-9223372036854776000 |
|
Max |
9223372036854776000 |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:QOS[:STATe] ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:QOS[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
OFF |
|
State Saved |
Yes |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:QOS:SIZE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
2 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:QOS:CONTent <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:QOS:CONTent? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:HT[:STATe] ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:HT[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
OFF |
|
State Saved |
Yes |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:HT:SIZE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
4 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:HT:CONTent <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:PAYLoad:MAC:HEADer:HT:CONTent? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
It is visible when Aggregated MPDU is set to on. The maximum number of MPDUs is limited to 1000.
Add a new MPDU.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU:ADD |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
|
|
State Saved |
Yes |
Delete the selected MPDU. Input parameter is the index of the selected MPDU.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU:DELete <integer> |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
|
|
State Saved |
Yes |
Copy the selected MPDU. Input parameter is the index of the selected MPDU.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU:COPY <integer> |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
|
|
State Saved |
Yes |
Displays the index for each MPDU. This cell cannot be edited.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:INDex? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Displays the number of octets in current MPDU, which is comprised of MSDU, MAC Header and MAC FCS.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:LENgth? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
290 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Indicates the number of octets in the current A-MPDU subframe, which is comprised of MPDU and Padded MPDU Delimiters. If the current MPDU is not the last one, its length cannot be shorter than Minimum MPDU Start Spacing, otherwise, MDPU delimiters will be padded after the current MPDU. If current MPDU is the last one, its A-MPDU Subframe Length is equal to its MPDU Length plus the length of one MPDU Delimiter(4 octets).
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:AMPDu:SFRame:LENGth? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Use this field to select the payload data source. The user data of the frame can contain the following data:
All 0s
PN9
PN15
User file
The user file must be in binary form. The least significant bit (LSB) of the first byte in the user data file will be the first bit of the user payload; the LSB of the second byte in the user file will be the ninth bit of the user payload, and so on. If User file is selected as the Data Type, the value displayed in the Data Length field will be equal to the length of the user's data file, up to the maximum data length.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:DATA:TYPE ALL|PN9|PN15|FILE
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:DATA:TYPE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
PN9 |
|
State Saved |
Yes |
Specify a seed in decimal format to generate a PN9 data sequence. The LSB of the seed comes out first. For example, if you enter a seed value of 10 (1010 in binary), the first 9 bits of the PN9 sequence are 0 1 0 1 0 0 0 0 0, with an increasing index from left to right. For more information, see PN Sequence Generation.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:DATA:PN9:SEED <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:DATA:PN9:SEED? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
511 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Specify a seed in decimal format to generate a PN15 data sequence. The LSB of the seed comes out first. For example, if you enter a seed value of 10 (1010 in binary), the first 15 bits of the PN15 sequence are 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0, with an increasing index from left to right. For more information, see PN Sequence Generation.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:DATA:PN15:SEED <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:DATA:PN15:SEED? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
32767 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Click the > button in this cell to select a user file as the data source.
The user file must be in binary form. The least significant bit (LSB) of the first byte in the user data file will be the first bit of the user payload; the LSB of the second byte in the user file will be the ninth bit of the user payload, and so on. If User file is selected as the Data Type, the value displayed in the Data Length field will be equal to the length of the user's data file, up to the maximum data length.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:DATA:FILE
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:DATA:FILE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
|
|
State Saved |
Yes |
Displays the number of data bytes in the user file when it is selected as the payload data source.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:DATA:FILE:LENGth? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-9223372036854776000 |
|
Max |
9223372036854776000 |
Set the number of data bytes in a frame. The value is limited by the MPDU Length.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:DATA:LENGth <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:DATA:LENGth? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
256 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Enable/disable the appending of a MAC FCS check sequence to the data payload.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:FCS ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:FCS? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
Click the > button displayed with this field to open the MAC Header Dialog, which enables or disables pre-pending the MAC header to the data payload. You can select General, RTS, CTS, or ACK format by clicking the down arrow in the top right corner of the Mac Header Dialog. You can set the desired data in each of the individual fields for each format. You can also disable these fields if the data is no longer desired by clearing the Mac Header (hex) checkbox.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer[:STATe] ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:TYPE GENeral|RTS|CTS|ACK
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:TYPE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
GENeral |
|
State Saved |
Yes |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:LENGth? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
30 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:FRAMe[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:FRAMe:SIZE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
2 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:FRAMe:CONTent <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:FRAMe:CONTent? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:DURation[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:DURation:SIZE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
2 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:DURation:CONTent <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:DURation:CONTent? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:ADDRess:A1[:STATe] ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:ADDRess:A1[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:ADDRess:A1:SIZE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
6 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:ADDRess:A1:CONTent <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:ADDRess:A1:CONTent? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-9223372036854776000 |
|
Max |
9223372036854776000 |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:ADDRess:A2[:STATe] ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:ADDRess:A2[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:ADDRess:A2:SIZE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
6 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:ADDRess:A2:CONTent <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:ADDRess:A2:CONTent? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-9223372036854776000 |
|
Max |
9223372036854776000 |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:ADDRess:A3[:STATe] ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:ADDRess:A3[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:ADDRess:A3:SIZE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
6 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:ADDRess:A3:CONTent <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:ADDRess:A3:CONTent? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-9223372036854776000 |
|
Max |
9223372036854776000 |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:SEQ[:STATe] ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:SEQ[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:SEQ:SIZE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
2 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:SEQ:CONTent <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:SEQ:CONTent? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:ADDRess:A4[:STATe] ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:ADDRess:A4[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
ON |
|
State Saved |
Yes |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:ADDRess:A4:SIZE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
6 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:ADDRess:A4:CONTent <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:ADDRess:A4:CONTent? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-9223372036854776000 |
|
Max |
9223372036854776000 |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:QOS[:STATe] ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:QOS[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
OFF |
|
State Saved |
Yes |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:QOS:SIZE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
2 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:QOS:CONTent <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:QOS:CONTent? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:HT[:STATe] ON|OFF|1|0
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:HT[:STATe]? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
OFF |
|
State Saved |
Yes |
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:HT:SIZE? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
4 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:HT:CONTent <integer>
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:RUSetup<channel>:USERsetup<channel>:MPDU<channel>:MAC:HEADer:HT:CONTent? |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
|
|
Max |
|
Sets the State to On for all RUs.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:ENABle:RU |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
|
|
State Saved |
Yes |
Sets the State to Off for all RUs except the first RU, which must remain On.
|
SCPI Command |
[:SOURce]:RADio:WLAN:WAVeform:BN:TB:DISable:RU |
|
SCPI Example |
|
|
Couplings |
|
|
Preset |
|
|
State Saved |
Yes |